VW ID. UNYX Body Parts: 11H, 89A and 11A Codes Explained (And Why They Do Not Cross-Fit)

On Tuesday morning, 4 November 2026, a WhatsApp voice note came in from Miguel Angel, who runs a five-bay independent workshop in Valencia, Spain. He repairs mostly imported Volkswagen ID.3 and ID.4, and lately a growing number of China-built ID. UNYX vehicles that local customers drive over from Valencia and Alicante. His message ran fifty-five seconds and it was about a single panel. “I have a customer waiting eight days for an ID. UNYX, a rear inner quarter panel. Your catalogue number for the imported ID.4 is sent, but the car in front of me has the SAIC-VW stamp on the VIN plate. Are these the same part? Because if I order the wrong one, I am the one standing in front of the customer explaining it.”

They are not the same part, and no supplier should have quoted him the imported number in the first place. What Miguel had hit is not a supplier problem, it is a numbering problem. Volkswagen split the MEB platform into two parallel part-number systems when it built the ID. UNYX in China with SAIC-VW: the imported cars carry codes that start with 1ED, 1EA, 3M0 or 5KE, and the China-built cars carry codes that start with 11H, 89A and 11A. The vehicles share a platform, a battery architecture and most of their electronics. The body-in-white does not share anything.

Miguel is not unusual. We get the same question roughly a dozen times a month now, from workshops in Spain, Poland, Portugal and the Netherlands, and it always arrives at the same moment: the customer has a car in the bay, the part is urgent, and two catalogues show a plausible-looking number for the same panel name. This guide is about how to tell them apart before the money moves.

Same Platform, Two Part-Number Systems

Start with the three-letter group code, because it tells you which numbering system a part belongs to before you read a single digit. On the imported MEB cars, the group codes you will meet most often are 1ED (ID.3, ID.4, ID.6, ID.7 family), 1EA (imported ID.4 and ID.5 variants), 3M0 and 5QE (bumper and rear body work on the ID. UNYX 08), 5KE (electronics) and 1KX. On the SAIC-VW built cars, the codes are 11H (front and mid body structure, and the ID. UNYX 06 bumpers), 11A (reinforcements and side panel supports), 89A (rear body and connection panels) and 12G, 11G (bumper covers across the UNYX and ID.6 range).

The reason the two sets do not cross-fit is geometric, and it is worth understanding rather than memorising. An inner quarter panel is not a flat pressing. It is a pressing that has to weld to a specific wheel arch, a specific seat rail, a specific roof rail and a specific crash structure, and it has to pass a side-impact homologation test that is signed off per body-in-white. The ID. UNYX body-in-white is not dimensionally identical to the imported ID.4 body-in-white. The rear door aperture, the B-pillar position and the rear floor pan geometry are different, and SAIC-VW runs its own press tooling. A 1ED quarter panel physically does not weld into an 11H body, and the same goes for the reverse.

The three OE families you will meet

Group code What it covers Typical vehicles
1ED, 1EA, 5KE Imported MEB structure, electronics, cooling ID.3, ID.4, ID.5, ID.6, ID.7
11H, 11A, 89A SAIC-VW structure and reinforcements Volkswagen Anhui ID. UNYX 06
3M0, 11G, 12G Bumper covers across both families ID. UNYX 06, 08, ID.4, ID.6

Every structural part we ship for an ID. UNYX carries one of these SAIC-VW group codes. If a quote reaches you with a 1ED number for a car whose VIN plate says SAIC-VW, that quote was built from the wrong catalogue, and no price negotiation will fix it.

How to Read a Structural Part Code in Five Steps

Take a real one from our own stock: 11H 809 447, B-pillar inner panel for the Volkswagen Anhui ID. UNYX 06. Here is how to decode it without a parts manual.

  1. Group code. 11H means SAIC-VW structural body parts. This alone rules the part in or out of the ID. UNYX range.
  2. Assembly group. 809 is the body-in-white and panel group. 807 is bumper covers and front exterior panels. 810 is floor, sill and lower inner structure. 121 is the cooling circuit.
  3. Part number. 447 is the specific pressing. Paired numbers such as 447 and 448 are usually left and right, but check the title, because 89A 809 347 and 348 are rear connection panels and 89A 810 421 A and 422 A are the lower inner quarter panels.
  4. Variant letter. The trailing A marks a revised or supersession generation. It is not optional. If a car was built in different production years, the letter can be the difference between a part that fits and a part that bolts on but does not seal or align.
  5. Surface suffix. GRU means the bumper cover is supplied in the OE primer finish rather than painted. That is a supplier specification, not a decoration, and it matters when you are matching a primered panel to an unpainted repair.

The letter at the end is not decoration

Miguel lost half an afternoon to this. He had the rear inner quarter panel right — correct group code, correct assembly group, correct part number — and then ordered the version without the A suffix. The panel arrived, went on the bench, and sat two centimetres proud of the B-pillar because the earlier generation was pressed against a different floor pan. The A suffix on 11H 809 421 and 11H 809 422 is not a revision note for the workshop; it is the difference between a two-hour fitting job and a return shipment.

Where the Two Systems Actually Diverge

It is reasonable to assume that on the same platform, most parts are shared. For an MEB vehicle built by the same company in the same era, a large share of the drivetrain and electronics really is shared. The exceptions are concentrated in four places, and those are the places where ordering errors happen.

Body-in-white geometry

This is the big one, and it is where the vast majority of our mis-order claims come from. B-pillar inner panels, inner quarter panels, rear connection panels, sill reinforcements and rear panel units are all unique to the SAIC-VW body. The 11H 809 447 and 11H 809 448 B-pillar inner panels, the 89A 809 347 and 89A 809 348 rear connection panels, and the 11A 810 327 A and 11A 810 328 A side panel reinforcements all exist only for the ID. UNYX. There is no imported equivalent to cross to, and that is not a sourcing failure, it is a design fact.

The rear panel unit is a good example of a part people underestimate. 11H 809 857 A is the primer-coated rear panel for the ID. UNYX. Because it is a structural closing panel rather than a cosmetic cover, the paint shop plans around it: it arrives primed, it goes into the primer booth, and it is welded to the rear floor. A workshop that orders it late, without primer and without a rack, discovers that the job cannot be scheduled until both arrive.

Bumper covers

Here both systems live side by side, which is exactly why bumper orders get mixed up. The ID. UNYX 06 uses 11H 807 221 A GRU for the front bumper cover, while the ID. UNYX 08 uses 3M0 807 221 GRU. The suffix GRU tells you both are supplied in primer, and the group code tells you which body they belong to. A workshop that works on both the 06 and the 08 will order the 08 part by reflex and end up with a cover that is thirty millimetres off in the lower corners.

Electronics

Here the overlap is partial and it changes by component. The on-board charger for the imported range is 1ED 915 691 J, with 1EA 915 692 M as the imported ID.4 and ID.5 variant. The battery control unit on the same family is 5KE 915 184 AD. The ID. UNYX uses its own high-voltage charging and battery electronics, such as the on-board charger for the ID. UNYX and the 12V front door lock actuator assembly that we see ordered alongside it. The rule that saves time is simple: electronics are shared only when the supplier confirms it against the VIN, because the software, the cooling plate interface and the connector keying can differ even when the part number looks familiar.

Cooling

Cooling is where the platform sharing is most useful and most confusing. 1ED 121 054 A, the coolant hose listed for the ID.3, ID.4, ID.6 and ID. UNYX, genuinely spans both build families for the parts of the circuit that SAIC-VW did not change. But the hoses that run through the ID. UNYX specific front structure are not on that number, and the ID. UNYX thermal management layout differs enough that a workshop should confirm the routing in the vehicle before ordering a coolant part.

Three Orders We Shipped in the Last 90 Days

These are real cases, with the mistakes removed, because the mistakes are the useful part.

Case 1: The rear quarter panel that was not a rear quarter panel

A workshop in Antwerp ordered what they described as a rear quarter panel for an ID. UNYX 06. Their VIN lookup returned 89A 809 347, which is a rear connection panel, not the quarter panel they needed, which is 89A 810 421 A. Both are 89A, both are rear, both fit the ID. UNYX 06. We shipped the correct pair, 89A 810 421 A and 89A 810 422 A, along with the two rear connection panels so the body shop had the full rear closing set in one container and one shipping document. The lesson is that the assembly group code 809 versus 810 was the only thing standing between them and a wrong delivery, and it is the second and third digits that carry it.

Case 2: A full panel set ordered model by model

A distributor in Wroclaw was moving from the ID. UNYX 06 to the 08 and asked whether one panel set would cover both. It will not. The 06 and the 08 differ in body dimensions and in bumper codes, so the sets are listed separately as Volkswagen ID. UNYX 06 full body panels and Volkswagen ID. UNYX 08 full body panels. Once that is accepted, the panel set is a much easier purchase than a mixed bag of individual pressings: four doors, front hood and rear tailgate in one line item, one colour-matched batch, one piece of paperwork.

Case 3: The urgent charger

A workshop in Milan had an ID. UNYX in the bay with a dead on-board charger and a customer leaving the next morning. The fastest path was not a catalogue search, it was reading the charger housing and confirming the connector keying and the software part number, because the ID. UNYX charging electronics do not come out of the imported 1ED 915 691 J bin. Once the correct charger was identified we shipped it by air, and the car left the next day. The lesson here is the same as in the first case: confirm the part against the vehicle, not against the platform.

A Six-Point Check Before You Order Structural Parts for an ID. UNYX

  1. Read the VIN plate and the build country. If it says SAIC-VW or Volkswagen Anhui, you are in the 11H, 11A and 89A world. If it says Germany or the Czech Republic, you are in the 1ED and 1EA world.
  2. Check the group code first. 11H, 11A or 89A confirms the SAIC-VW system. Anything starting 1ED or 1EA on an ID. UNYX needs a second look.
  3. Confirm the model variant. The 06 and the 08 are different bodies. The bumper code alone, 11H 807 versus 3M0 807, tells you so.
  4. Match left and right in one line. Paired numbers are a package. Order one and you will pay a second freight charge for one panel.
  5. Read the trailing letter and the finish suffix. The A suffix is a generation, and GRU means primer finish. Both change what happens in your paint shop.
  6. Order the closing set, not the single pressing. If the vehicle needs a rear quarter panel, it very often needs the connection panels and the reinforcement beside it. Bundling them into one order removes a second freight line and a second week.

What Changes When the Vehicle Is a China-Built ID. UNYX

Two practical effects worth planning for. First, the structural catalogue for the SAIC-VW cars is smaller and newer than the imported range, which means fewer sources per part and longer replenishment on the reinforcement and inner-panel side. Panels that take three weeks in the imported range can take six in the UNYX range, and a workshop with a customer waiting does not have six weeks of patience. Second, because the UNYX range is younger, the variant letters move faster. A number that was correct for a 2024 car can be superseded for a 2026 car, so the production date matters as much as the vehicle model.

The upside is real as well. Because the ID. UNYX parts are made for the Chinese market in volume, the structural panels are in better supply than the equivalent European-market parts, and full panel sets can be ordered at workshop-friendly quantities without a container of your own. For a workshop that does one or two ID. UNYX jobs a month, ordering a panel set directly is usually cheaper and considerably faster than trying to find a European wrecker with the right pressing in the right generation.

What We Tell Customers Who Ask Us This First

Almost every week someone asks us the same thing: can you just send me the part for the ID. UNYX that looks like the ID.4 part? The honest answer is that we can send you the part that fits, and we will tell you exactly which vehicle it belongs to, but we cannot send you a part that belongs to a different body-in-white, because it will not be the same part.

What we do instead is ask for three pieces of information before we quote: the VIN or the VIN plate photograph, the production year, and whether the repair is cosmetic or structural. That is enough to place a part in the right family, pick the correct generation letter, and tell you whether the paint shop needs a primed pressing or a finished one. It takes ten minutes and it removes the single most expensive mistake in this whole category, which is a part that arrives, does not fit, and has to go back.

Because the ID. UNYX and the imported ID.4 are two different cars wearing the same platform badge. Read the group code before you read the price.

— Wang (JLL Auto Parts founder) · 13 years sourcing EV parts from Shanghai · jllautoparts.com

Shopping Cart
Scroll to Top