Incoterms and Container Density: What Really Decides Your EV Parts Landed Cost in 2026

Last Thursday evening, a WhatsApp voice note came in from Thierry, who runs a six-bay independent workshop in Lyon and repairs mostly ZEEKR and Li Auto imports. His message ran fifty seconds, and it was not about a part. “I have a quote for a full body panel set for a ZEEKR 001. The parts are €2,100. The freight is €840. My supplier wants me to take DDP so that I do not have to deal with customs. So I am paying €2,940 and I still do not know what I am actually buying.” He had a second quote sitting in the same chat, for an on-board charger at €540 with €70 of freight, and he wanted to know why those two numbers were so far apart.

Thierry asked the right question, and it is the question almost every workshop owner ends up asking after their first container lands. The short answer is that the two quotes were not priced the same way. The panel set is heavy, awkward and low value per cubic metre; the charger is the opposite. And the DDP line on his quote did not describe a free service. It described a legal transfer of responsibility that he had not yet asked to read.

There are two numbers that decide what a Chinese EV part really costs you, and neither of them is the unit price or the freight rate. The first is where risk and cost move between you and the supplier, which is what the Incoterm allocates. The second is how much volume the goods occupy, which is what your freight is actually paying for. The first is written on the quote. The second is usually missing from it entirely.

The Part You Are Least Worried About Is Often the One That Costs Most to Move

Thierry’s two quotes were both correct, and both incomplete. What he was missing was that freight is charged per container, not per part, so what actually sets the freight is the volume the goods fill and the weight they carry.

Look at what a body panel order physically is. A complete set such as the ZEEKR 001 full body panel set is four doors, a front hood and a rear tailgate, each one a large, flat, mostly empty shape. A set like the Li Auto L7 full body panels is the same story. The AVATR 11 full body panels and the Deepal S05 full body panels are no different. They nest badly, they need separator boards between layers, and they cannot be stacked like a crate of brake discs. The cardboard around them is mostly air.

Now take the on-board charger in the same order. A unit like the ZEEKR 009 on-board charger is a dense metal box, it packs into a gap next to something else, and it will happily travel as a small part of a mixed consignment. Same container. Same freight invoice. One of those two goods is paying for the air around it.

That is why the honest comparison is not €2,100 against €540. It is €2,100 plus a share of the container against €540 plus a smaller share of the container. Once you calculate it that way, panel sets are not expensive to ship because they are expensive. They are expensive to ship because they are big.

The two categories that make this obvious

Bumper covers sit in the same place on the curve as body panels. The VW ID.4 bumper cover and the Toyota bZ4X front bumper cover are big, thin and hollow, which is the worst possible combination: they take up container space and then they float, because the packaging volume is far larger than the material.

At the other end of the scale, wiring harnesses are close to ideal freight. The ZEEKR 001 high voltage wiring harness, the ZEEKR 001 centre console wiring harness and the ZEEKR 001 front door wiring harness are long and awkward, but they roll, they fold, and they fill a carton without leaving much void. Headlamps sit somewhere in the middle: the ZEEKR 001 headlamps and the Honda NS2 right headlight assembly are dense and high value, but fragile, so they need crate space and careful packing.

What Each Incoterm Actually Allocates — and What It Does Not

Incoterms are the international trade rules for who arranges carriage, who pays for it, and where the risk of loss passes from one party to the other. The current set is Incoterms 2020, and it has not changed since. What changes every year is that suppliers misquote them, buyers accept them without reading them, and the first surprise arrives at the port.

The single most misunderstood feature of the whole system is this: cost and risk do not move at the same point. Under CFR and CIF, the seller pays the freight all the way to your destination port, but the risk still transfers when the goods are loaded on board at the origin. If the container is damaged at sea, the seller is not liable — because the risk already moved three weeks earlier.

Incoterm Seller pays up to Risk moves You still pay Where it suits a parts buyer
EXW Goods made available at their premises At the supplier’s gate Origin handling, export clearance, main carriage, insurance, import clearance, duty, VAT You already have a freight forwarder and want maximum control of cost
FCA Goods delivered to your carrier at the named place When the carrier takes the goods Main carriage, insurance, import clearance, duty, VAT Air, road and container shipments where you control the forwarder
FOB Export clearance and loading on board at origin Once on board the vessel Main carriage, insurance, import clearance, duty, VAT Sea freight, when you want the seller to handle export paperwork
CFR Cost plus freight to the destination port Once on board at origin Insurance, import clearance, duty, VAT Sea freight where you want freight cost locked into the goods price
CIF Cost plus freight plus minimum insurance Once on board at origin Import clearance, duty, VAT Sea freight where you want cover arranged but are not ready to buy a policy yourself
DDP Delivery at your door, including import clearance and duties At your door Almost nothing, and that is the point Small first orders, or buyers who genuinely have no import experience

Read the risk column against the cost column one more time. Under CFR and CIF the seller is paying for the entire sea leg, but the risk sat with them for about twelve hours and then it was yours. That gap — three weeks of ocean transit — is exactly why insurance terms, carton quality and packing method belong in the same conversation as the Incoterm, and not in a follow-up email three days later.

What DDP actually hides from you

DDP is the term suppliers offer most often, and it is the one that requires the most questions. Under DDP the supplier is the importer of record. They clear your import, they pay the duty, and they deliver to your address. For a first order from a workshop with no import experience, it is genuinely the right choice, and we tell customers that.

But you should know what you are not seeing. You are not seeing the customs entry, so you cannot verify how the goods were classified or what duty was actually assessed. You are not seeing the VAT treatment, which matters if you intend to reclaim it. And you are not seeing the freight document, which means you have no visibility over the packing, the container condition or the delivery date. Ask for the import entry and the freight document before you accept DDP on anything above a few hundred euros, and treat them as part of the delivery, not as a nicety.

Where EXW genuinely wins

There is a case for EXW that is worth stating, because most advice on this topic is one-sided. If you already work with a forwarder who consolidates shipments from several Chinese suppliers, EXW can be the cheapest way to buy, because your forwarder’s rate card beats a supplier’s single-shipment price. You also keep control of the insurance and the packing standard, which are the two variables that decide whether a shipment arrives intact. EXW is a bad choice for a buyer with no freight process. It is the best choice for a buyer who has one.

Container Density: The Number Nobody Puts On The Quote

Your freight is charged per container or per cubic metre. So the question your supplier should be answering, and usually is not, is simple: how many of my sets fit, and what does each set therefore cost me?

The table below is a worked example using our own assumed packing volumes, so that you can see the method. It is not a promise and it is not a quotation. Take the assumed packed volumes, replace them with your own measurements or your forwarder’s, and the arithmetic gives you the number that matters for your order.

Goods type Assumed packed volume per unit Units per 40ft HC (worked example) Freight per unit (worked example) Typical share of goods value
Full body panel set (4 doors, hood, tailgate) 2.4 – 3.0 m³ 25 – 31 sets €27 – €34 12 – 17%
Bumper cover, single 0.5 – 0.7 m³ 110 – 150 covers €6 – €8 3 – 6%
Headlamp assembly 0.15 – 0.22 m³ 345 – 500 lamps €1.70 – €2.50 1 – 3%
Wiring harness set 0.08 – 0.12 m³ 630 – 950 sets €0.90 – €1.40 Under 2%
Control unit or module 0.01 – 0.02 m³ 3,800 – 7,600 units €0.12 – €0.25 Under 1%

Two things fall out of this table. First, the freight share of goods value is not a fixed percentage — it can be under one percent for a module and above fifteen percent for a panel set, from the same container and the same rate. Any quote that gives you a single blended freight percentage has not understood your order.

Second, the break-even point is where value density crosses volume density. Once you are sending a mixed consignment of panels and modules, the modules are effectively free to ship, because they ride in the voids around the panels. That is the commercial argument for consolidating rather than ordering panel sets and small parts from separate suppliers, and it is the argument we make most often to customers who were about to place two separate orders.

Ask for three numbers before you accept any freight quote

  1. The total volume of your goods in cubic metres, measured packed, not assembled.
  2. The total gross weight in kilograms, because you will hit the weight limit before the volume limit more often than you expect.
  3. The number of units that will actually be loaded, so the per-unit freight can be divided out.

If a supplier cannot give you those three numbers, they are quoting you a lump sum, and a lump sum is exactly how Thierry ended up unable to tell whether €840 was a good freight price or an expensive one. It might have been either. That is the problem.

Doing the Landed Cost Properly

A landed cost is only meaningful when every cost sits on the same side of the comparison. Build it in this order, and build it for the two options side by side, because the Incoterm changes which lines are yours.

  1. Goods value — the unit price at the agreed Incoterm.
  2. Freight — the share of the container your goods occupy, or the full amount under DDP.
  3. Insurance — nil under CIF if you accept the minimum cover, or your own policy otherwise.
  4. Origin handling and export clearance — yours under EXW and FCA, the seller’s under FOB and above.
  5. Import duty — the single line item that surprises buyers most, because it is charged on the customs value, which is the goods value plus freight and insurance.
  6. VAT — payable on goods plus duty plus freight. Worth checking whether you can reclaim it, because for a VAT-registered workshop it is a timing cost rather than a real one.
  7. Port, terminal and delivery charges — small individually, and never zero.

Apply that to Thierry’s two quotes and the picture changes. The body panel set is €2,100 of goods that occupy roughly 2.7 m³ and about 190 kg, so the freight share lands near €30 – €35 per set once it is divided across the load — not the €840 he was staring at, which was the whole container. The charger, by contrast, contributes almost nothing to the volume and therefore almost nothing to the freight.

What Thierry should have done, and what we recommend to anyone in his position, is ask for the panel set and the charger in one order against one Incoterm, and ask for the freight as a per-unit line rather than as a total. If the supplier quotes DDP, ask for the import entry underneath it so you can see the duty assumption. Then you can compare a panel set and a charger on the same basis, which is the only comparison worth making.

Three Buyers, Three Incoterms

The right answer depends on what you actually are, and pretending otherwise is how people end up paying twice.

The one-bay importer who has never cleared customs

Take DDP, on a small order, with a supplier who does this every day. The additional cost is usually a few percent of the goods value, and what you are buying is the absence of a customs problem on a day you do not have time for one. This is the right answer for a first container, and there is no shame in it. Then read the import entry when it arrives, and move to a cheaper term once you know what you are doing.

The growing workshop with its own forwarder

Take EXW or FCA and control the freight yourself. You will save the margin the supplier built into its freight, you will consolidate with other suppliers, and you will set the packing standard. The cost is that you now own insurance, the packing instructions and the delivery delay. If you are sending more than one container a quarter, this is almost always the cheaper option once the maths is done properly.

The distributor with real volume

Split the difference the way experienced distributors do: FOB for the goods and freight you control on the sea leg, so that you can consolidate across several suppliers into one container. The ZEEKR 007 full body panels, the ZEEKR 009 full body panels and the Li Auto L8 full body panels are the kind of goods that fill a container properly when you are buying at that scale, and the AVATR 12 full body panels and the Deepal G318 full body panels are the kind you consolidate alongside them. Consolidation is the single biggest freight saving available to an importer, and it only exists if you control the freight leg.

Seven Questions to Ask Before You Accept an Incoterm

  1. Which Incoterm is this, in its full form, and where does risk transfer?
  2. Is the quoted price EXW, FOB, CFR, CIF or DDP — and does the quotation say so in writing?
  3. Who arranges and pays the export clearance?
  4. What is the packed volume and the gross weight of my goods?
  5. How many units will actually be loaded into the container?
  6. Is the freight quoted per container, per cubic metre or per unit?
  7. If it is DDP, can you have the import entry and the freight document?

If the supplier answers the first two questions clearly and the fourth and fifth with numbers, you are dealing with someone who understands the shipment. If they cannot answer the fourth and fifth, you are paying a lump sum for a container and you will not know what your parts cost until it arrives.

What Has Changed For EV Parts Specifically

Incoterms have not moved since 2020, but the EV parts trade has moved around them in ways worth knowing.

First, the parts getting shipped are getting bigger. The mix has shifted from modules and sensors toward full body panels and complete door sets, because the Chinese EVs reaching Europe are new models whose body panels are not yet in any European parts network. Our own Li Auto i8 full body panels and the ZEEKR 9X full body panels are typical of the new wave, and both are volume-heavy freight. That pushes the average shipment towards panel sets, and panel sets are exactly the goods where the density number decides your margin.

Second, a single container now carries parts for several models more often than one, because workshop owners are ordering smaller quantities of more models. That is good for the buyer on price per part and bad for the buyer who assumed one container means one model. It also means the freight share drops, which is worth understanding before you negotiate hard on the goods price.

Third, packing is no longer a detail, because the failure that costs you money is rarely the failure of the part itself. It is the arrival of a panel set with a corner crease, or a harness with a crushed connector, and both of those are packing failures. Insisting on separator boards, corner protection and a photograph of the loaded container before it is sealed costs nothing and settles most of the disputes we have seen.

Fourth, the parts that are hardest to ship are the ones that pay the best. A VW ID.4 on-board charger and a VW ID.3 battery control unit are high value and low volume, so they are the cheapest freight you will ever buy. If a supplier quotes you a body panel set and a control unit at the same freight rate per unit, they have not looked at the container, and the control unit is subsidising the panels.

What We Tell Customers Who Ask Us This First

We tell them to stop comparing quotes on the goods line and start comparing them on landed cost, and we tell them that the two numbers they need are the packed volume of their order and the Incoterm their supplier is offering. Everything else — the freight rate, the duty rate, the total — follows from those two.

We also tell them that DDP on a first order is a perfectly reasonable choice and not a sign of naivety. What is not reasonable is paying DDP for three years because nobody asked the supplier to price the same goods FOB. Ask once, on the second order, and you will have a number you can compare. We have had customers do exactly that and move €40 to €60 of freight cost out of every panel set they order, which on a container of panels is more than most people expect.

And if you are still unsure, send us the two quotes you are looking at, with the Incoterm printed on each, and we will tell you which one is cheaper once the freight is divided across the units. We have done this for workshops across Europe, and more than once the answer has been the opposite of what the customer expected.

Because the cheapest quote on a page is not the cheapest part in your workshop. It is the quote where somebody counted the container, and nobody else did.

— Wang (JLL Auto Parts founder) · 13 years sourcing EV parts from Shanghai · jllautoparts.com

Shopping Cart
Scroll to Top