Toyota bZ4X and Honda NS1 Part Numbers: How to Decode OEM Codes and Match the Right Supplier (2026 Sourcing Guide)

Three Numbers, One Part: Why Your Part Number Changes Depending on Who Quotes It

Last Tuesday morning, a WhatsApp voice note came in from Marco in Bologna. He runs a six-bay bodyshop north of the city, mostly Toyota bZ4X and Honda NS1 work, with the occasional XPeng G6 booked in for a lidar replacement. His message was short: “I have the number for the rear brake disc, 424310R050. Three suppliers sent me three different prices and one of them sent me a front brake line. How?”

Marco had done nothing wrong. He had asked three suppliers for the same part number, and got three different interpretations back. The reason is that the number printed on the Toyota service catalogue is not always the number on the box, and it is certainly not always the number a trading company put in its spreadsheet.

There are, in practice, three numbering systems in play at once. The OEM catalogue number identifies the part as Toyota built it. The supplier or internal drawing code identifies the same part as the factory that actually makes it. The aftermarket cross-reference number is what a trading company uses to find the part in its own warehouse system. Same physical part, three identifiers, and every one of them is legitimate.

This guide is the decoding method I use when Marco — or any workshop owner — sends me a number and asks what it actually is. It is also the method our own purchasing team uses before anything goes on a purchase order to Shanghai. Getting it right is the difference between a body panel arriving in a crate you can unload with a forklift and a tailgate lamp arriving in an envelope.

The single most useful habit I can give a workshop owner is this: never order from a number alone. Order from a number plus a fitment check, plus a photo of the part you are replacing, plus the VIN or the model year. That is the whole method. Everything below is detail on how to do each of those three checks cheaply.

Toyota bZ4X: Reading Chassis and Body OE Numbers

Toyota’s catalogue numbers for the bZ4X follow a readable pattern, and they are among the easiest in the Chinese EV market to decode. The rear brake disc on the bZ4X is 424310R050 Rear Brake Disc — a ten-character code where the first five digits are the Toyota base part number and the trailing letters carry the revision and fitment information.

The suffix is where buyers get hurt. A part ending in R050 and the same part ending in R120 are not interchangeable across the range, even when the base number looks identical. Compare the bZ4X steering wheel listings: 451000R280C0 Steering Wheel Assembly and 451000R310C0 Steering Wheel Assembly are both described as a steering wheel assembly for the same vehicle, but they carry different suffix codes and different trim levels. The catalogue knows which one fits which build. Your supplier has to know too.

The same discipline applies to running gear. The bZ4X front axle hub sub-assemblies exist in right-hand variants with different codes — 435500R100 Front Axle Hub Sub-Assembly RH and 435500R110 Front Axle Hub Sub-Assembly RH — and matching them to the wrong side is a very expensive mistake on a part that is not returnable once it is on the bench.

Body and glazing numbers are even more slippery. The bZ4X quarter window assembly 627100R140 Quarter Window Assembly RH and the roof sliding glass sub-assembly 632010R241 Roof Sliding Glass Sub-Assembly RH, No. 1 both look like glass numbers, but one is a fixed bonded part and the other is a sliding assembly in a track. The carrier and channel for the sliding unit is a separate item entirely, and a supplier who quotes only the glass will leave you with a piece you cannot install.

My rule for Toyota: treat the last three characters as the part, not the whole string. Read the base number for the component, then read the suffix for the revision, then confirm the fitment against the model year. It takes ten minutes and it removes the single largest source of returns I see from European buyers.

Honda NS1 and RS1: Supplier Codes That Do Not Look Like Part Numbers

Honda is the opposite problem. The NS1 and RS1 use codes that do not resemble an OEM catalogue number at all — they look like drawing numbers, and they often are. 6701031AH00ZZ Front Door RH is a front door assembly for the Honda NS1, and 67510-31A-H00ZZ Rear Door RH is the rear door for the same car. Nothing in those strings tells you they are a matched pair.

This is where the distinction between the OEM number and the supplier code becomes expensive. When a part is a large stamped or bonded assembly, the factory that builds it for Honda frequently produces to its own drawing revision, and that internal code becomes the only code on the part. The OEM catalogue number is a layer that sits above it in the parts system.

For an independent workshop, the practical implication is that you should always give a supplier at least one of these alongside the code: the VIN, the build date, or a photograph of the OE label on the part you are pulling. We had a customer in Lyon order 78501-31Y-H10ZA Steering Wheel [Natural Black], a steering wheel for a Honda NS1, with a code only. It arrived for an NS1 of a different production window. The steering wheel itself was fine; the trim fit was not.

The same applies to the larger Honda assemblies. The NS1 hood 60100-33T-H00ZZ Hood / Bonnet, the NS1 tailgate 68100-31A-H00ZZ Tailgate / Hatchback Door and the NS1 combination meter 78100-31A-H11 Combination Meter / Instrument Cluster are all parts where a near-miss is close to a write-off, because the part is expensive, the paint is already applied, and you cannot easily resell it into another car.

A note on the electronic parts: an NS1 display unit assembly such as 8A70031AH01 Display Unit Assembly and the RS1 equivalent 8A50031AH11 Display Unit Assembly are close enough in description to be confused, and the RS1 part is not a drop-in for the NS1 even though the housing is similar. The receiver drier / desiccant 80102-T6A-003 Receiver Drier / Desiccant is a good example of a cheap part that people routinely over-order — ask for the quantity the workshop actually needs rather than a carton.

VW ID.3: Where the Number Comes From and Why Group Codes Mislead

Volkswagen codes carry a system prefix, and that prefix tells you the platform family rather than the individual vehicle. A code beginning 3M0 — such as 3M0 807 221 GRU Front bumper for VW ID. UNYX 08, the front bumper for the VW ID. UNYX 08 — sits in one platform family, while 4K4 codes like 4K4907117H 360 Camera Control Module for Audi Q7, a 360 camera control module for the Audi Q7, sit in another. Same manufacturer group, same software environment, completely different parts.

This is why ID.3 buyers get caught. The ID.3 shares more architecture with the wider VW group than its badge suggests, but it is not a Golf and it is not an ID.4. A generic VW part number that a seller found in a group catalogue will often be listed as ID.3 compatible on the strength of a shared platform code and nothing else.

Our own position is that we list complete sets rather than loose panels for exactly this reason. The Volkswagen ID.3 Full Body Panels – 4 Doors + Front Hood + Rear Tail… full body panel set for the ID.3 ships with four doors, front hood and rear tailgate as one matched group, and the fitment of those five components against each other is exactly what an individual panel buyer cannot verify from a code alone. When a set is assembled by one supplier, the gaps line up. When you buy panels from four suppliers, they may not.

The same logic runs through the rest of our range. Where a vehicle has a factory-consistent body group, we offer it as a set: the Toyota bZ3 Full Body Panels – 4 Doors + Front Hood + Rear Tailgate Toyota bZ3 set, the Toyota bZ4X Full Body Panels – 4 Doors + Front Hood + Rear Tailgate Toyota bZ4X set, and the Audi Q4 e-tron Full Body Panels – 4 Doors + Front Hood + Rear Tailgate Audi Q4 e-tron set all follow the same four-door-plus-hood-plus-tailgate format. Buyers who are restoring or rebuilding a single vehicle usually want the set; buyers doing a single-panel insurance repair usually want the piece.

A Seven-Step Method to Match Any OE Number to a Supplier Listing

This is the sequence I give to Marco and to every workshop owner who asks. It is deliberately unglamorous, and it works for a €30 sensor as well as for a €4,000 body panel set.

Step one: pull the number off the part itself, not from a listing. If the part is already off the car, photograph the label. If it is still on the car, photograph the label before you remove anything. This one habit prevents more wrong orders than any other.

Step two: split the code into base and suffix. For a Toyota-style code, that is the first five characters and everything after. For a Honda-style drawing code, it is the prefix and the revision block. Write both down. If a supplier cannot tell you which part of the code they matched, that is the answer.

Step three: get the model year, and get the build date if the vehicle is a 2024 or newer build. Chinese EV model years are approximations; production windows cut inside them.

Step four: identify the position on the vehicle in plain language. “Rear left,” not “RH,” because RH versus LH conventions are not universal across the brands you will be buying from. Then state whether it is a single part or part of a set.

Step five: check whether the part is returnable. Fasteners, seals, fluids and electronics with a programmed VIN are not. Body panels and glass usually are only if they are undamaged and unopened, which is a very narrow definition.

Step six: get the lead time in writing, split into production and shipping. We quote the same way to Marco and to a distributor in Hamburg: production days, then the Shanghai-to-Rotterdam or Shanghai-to-Milan transit, then a customs buffer. On body panels our realistic transit is 12 to 15 days by sea; on small electronic items it is faster by air.

Step seven: pay attention to what the invoice line actually says. It should contain the number, the description, the quantity, and the fitment you supplied. If the description is a marketing sentence instead of a part name, ask for it again — a marketing sentence is what happens when a supplier is guessing, and they are probably guessing.

Five Mistakes That Show Up Every Single Week

The first mistake is ordering by description alone. “Front bumper for bZ4X” is a category, not a part. The bumper cover 521190R949 Front Bumper Cover and the front bumper side support sub-assembly 514410R131 Motor Under Cover, No. 1 both answer to that description, and they cost very different amounts and fix very different problems.

The second is treating a base number as a complete number. The bZ4X steering intermediate shaft 452200R040 Steering Intermediate Shaft Assembly and the bZ4X power steering gear assembly 442500R120 Power Steering Gear Assembly are frequently quoted with the same base by suppliers who have not read the suffix. Ask for the suffix every time.

The third is assuming a housing match is a function match. A steering column assembly 53220-31Y-H12 Steering Column for the Honda NS2 and a combination meter 78100-31A-H11 Combination Meter / Instrument Cluster for the NS1 both look like dashboard components. One is a structural part, the other is an electronic display — the fitment note matters more than the photo.

The fourth is ordering a whole set when you need one piece, or vice versa. On a collision repair the practical unit is the panel; on a rebuild the practical unit is the set. Ask the supplier which way they would cut the set if you wanted only the hood, and what the price difference is. A good supplier will tell you both numbers without hesitating.

The fifth, and the most expensive, is skipping the fitment check on a part that will be painted. A hood like 6010031AH00ZZ Hood / Bonnet for the Honda NS1 and a cowl panel sub-assembly like 551010R191 Cowl Panel Sub-Assembly for the bZ4X both look correct on a workbench and both are wrong for at least one build window. Painted, they are scrap. Checked, they are parts.

What a Clean Purchase Order Looks Like on Our Side

When Marco’s order went out, the line items read like this: 434300R020 Front Drive Shaft Assembly RH front drive shaft assembly RH for the bZ4X, 424310R050 Rear Brake Disc rear brake disc for the bZ4X, 44014-31A-305 Outer Joint Kit / CV Joint Outboard Kit outer joint / CV joint kit for the Honda NS1, 45022-31A-H00 Front Brake Pads front brake pads for the Honda NS1, 50630-31A-H01 Engine Mounting Bracket engine mounting bracket for the Honda NS1, and the Volkswagen ID.3 Full Body Panels – 4 Doors + Front Hood + Rear Tail… ID.3 body panel set.

Every line had three things attached to it: the number as printed on the part, the fitment note in plain language, and the photo Marco had sent from the dismantled vehicle. When the crate landed in Bologna eleven days later, the doors went on without a modification. That is the entire goal of this guide — the difference between a part that fits and a part that is nearly right.

If you are standing in front of a dismantled vehicle right now with a number in your hand and no idea what it is, send it to me with a photo and the model year. I will tell you what the part is, whether we stock it, and what the realistic lead time is — even when the answer is that we do not carry it and I would rather you buy it elsewhere than wait for a bad match.

Because the whole business only works if the part fits. Thirteen years of sourcing from Shanghai taught me that the cheapest part in the world is the one that goes straight onto the shelf, and the most expensive mistake is a mismatched panel with paint on it.

— Wang (JLL Auto Parts founder) · 13 years sourcing EV parts from Shanghai · jllautoparts.com

Shopping Cart
Scroll to Top